logo
POLYCOATINGS INTERNATIONAL
YOUR SOURCE FOR ELASTOMERIC ROOF COATINGS,
WATERPROOFING SOLUTIONS & RUST CONTROL

Celebrating Our 18th Year in Coatings 1991—2009
HOME CONTACT US

NEW PRODUCTS

SAFE-T-KOTE RINSEABLE PRIMER FOR EPDM RUBBER ROOF MEMBRANE
                             
Safe-T-Kote Rinseable Primer is our newest development in primer technology for elastomeric roof coatings. Safe-T-Kote Rinseable Primer is a low viscosity sprayable liquid used to pre-treat black EPDM rubber roof membrane prior to power washing and application of the roof coating. The product improves coating adhesion, affording longer roof protection.

Safe-T-Kote Rinseable Primer is designed for use with Safe-T-Plex 520 Elastomeric Roof Coating.
 

TYPICAL PHYSICAL PROPERTIES

The following are typical physical properties of Safe-T-Kote Rinseable Primer, however they should not be regarded as specifications:

Appearance

Clear liquid

Color

Pink to purple

Odor

Mild

pH

6 – 7

Specific Gravity (g/cc)

1.01

Density, wet (lbs/gal)

8.46

Solubility in water

Completely soluble

 

RECOMMENDED APPLICATION INSTRUCTIONS ON A ROOF

 

      1. Apply Safe-T-Kote Rinseable Primer via a sprayer (Hudson-type agricultural, or airless) at an              application rate of 500 square feet/gallon.

2. Use a 3 – 4 foot arc pattern.

 

3. Allow Safe-T-Kote Rinseable Primer to stand for a minimum of 15 minutes.

 

4. Clean EPDM with a commercial power washer (between 2000-3500 psi). When cleaning the EPDM, it should be done slowly and close to surface in order to remove mica and inorganic release agents.

 

5. Rinse thoroughly with power washer. The rinse step may be done at a faster pace than the cleaning step. The final rinse water should be clear with no soap bubbles present.

 

6. The EPDM will range from muddy brown to black after washing with Safe-T-Kote Rinseable Primer

 

7. When the surface is dry, coating can begin.

 

SAFE HANDLING INFORMATION, PRECAUTIONS:

 

1. Thoroughly read MSDS for product – It is important to note that Section 13 of the MSDS titled “Disposal Considerations” discusses spills of undiluted Safe-T-Kote Rinseable Primer. These undiluted spills are different from the rinsate referred to below in the technical notes. The rinsate is defined in these notes as the roof washings composed of diluted Safe-T-Kote Rinseable Primer that result from the proper use of the product according to the application guidelines. In general, during the pressure washing of a roof, one part of Safe-T-Kote Rinseable Primer is diluted with 300 parts of water.

 

2. Ensure proper drainage:

We recommend the use of prudent judgment regarding the release of roof rinsate containing Safe-T-Kote Rinseable Primer into the environment. Based on aquatic toxicity data, this primer is classified as of LOW CONCERN to aquatic invertebrates and fish, according to the USEPA TSCA classification criteria, i.e., the LC/EC50 > 100 mg/L.

The results indicate that the lethal or effective (functional) concentration affecting 50% of the tested population is greater than 220 mg/L of Safe-T-Kote Rinseable Primer for fish, and aquatic invertebrates. Safe-T-Kote Rinseable Primer is classified as of moderate concern to algae according to USEPA TSCA classification criteria, i.e. the LC/EC50 is between 1 mg/L and 100 mg/L. Dilution of the primer with rinsate and subsequent added dilutionary capacity of receiving streams, rivers or ponds would likely buffer any potential for adverse effects.

Because of the low toxicity of the formulation to fish, aquatic invertebrates and algae it is unlikely that releases of the diluted Safe-T-Kote Rinseable Primer material into a storm sewer will cause adverse impact to exposed organisms. The numbers and diversity of organisms in these non-natural systems are anticipated to be low. Increased dilutionary capacity of any receiving water body will serve to further mitigate any potential for adverse effects. Without detailed plans regarding the receiving water course at the site in question, caution should be exercised. Release of rinsate into pristine or near pristine water courses should be avoided.

Note that compliance with local regulatory ordinances regarding releases of the rinsate into the aquatic or soil compartments should be ensured prior to any disposal operation.

 

Polycoatings International, 324 Saunders Road, Unit 8, Barrie, Ontario, Canada  L4N 9Y2

Tel: Toll Free 1-877-434-1658   Email info@polycoatings.com